HARDWARE SYSTEM REQUIREMENTS
Pentium 4 or equivalent · 2 GHz or better
PCI2.2/PCI-X/PCI-E with 3.3V power supply
|
Telephony
Interface
Trunk type: T1/E1
Trunk Interface Digital High Impedance (Z)
AC Impedance 1k Ohms
Input Impedance 1000 Ohm +/- 5%
Maximum Tap Length 30m (100 feed) of CAT 3 cable
Connectors Two RJ-45 connectors |
|
OPERATING SYSTEMS
Windows 2000 · Windows XP
Windows 2003 32 bit· Linux (Call for variant details)
Technical
Specifications
Max boards per system: Any combination up to 512 ports
Max ports per system: Up to 512
Resource Sharing Bus: MVIP or H.100
Boards Status: On-board LEDs
Clocking: Master/Slave |
T1
Interface
Receive Clock Rate 1.544 MHz +/-200ppm
Transmit Clock Recovered RX clock or 50 ppm
Input Level LBO 0dB to -22dB
Framing SF (D4), ESF
Line Coding AMI, B8ZS
Signaling Protocol ISDN, NFAS, CAS
Clock and Data Recovery Complies with AT&T TR62411
and Bellcore TA-TSY-000170
Loss of Signal Detection ANSI T1.231
Alarm Detection and Integration LOS, LOF, Yellow, and AIS per
ANSI T1.231
Binary Sequence Detector Per ITU-T 0.151 |
Environmental Conditions
Operating Temperature: 0C to +60C
Storage Temperature: -20C to +85C
Humidity: 8% to 80% non-condensing
Storage humidity: 8% to 80% non-condensing
Physical
Characteristics
Form Factor: Full-size PCI card
Power
Requirements (6409)
+ 3.3 VDC: 2.8 A
+5 VDC: 5 mA
-12 VDC: n/a
+12 VDC: 20 mA |
E1
Interface
Receive Clock Rate 2.048 +/- 175ppm
Transmit Clock Recovered RX clock or 50 ppm
Input Level 3.2V down to 0.45 V
Framing Basic G.704, CRC-4
Line Coding AMI, HDB3
Signaling Protocol ISDN, DASS2, CAS
Loss of Signal Detection per ITU-T G.775
Alarm Detection and Integration LOS, LOSMF, TS16, CRC
Binary Sequence Detector Per ITU-T 0.151 |
SDK
Ai-Logix Native SmartWORKS™ API
SmartControl (Control Panel)
SmartVIEW (Card functionality test application)
Host
Interface
Bus Compatibility: Complies with PCISIG Bus Specifications, Rev. 2.2
Bus Speed: 33 MHz
Bus Mode: 32 bit bus master/target |
Audio
Signal
Receive range: -68 dBm to + 3 dBm
Input gain control: +24 to -50 dB
Silence Detection: Programmable from API
Transmit volume control: +24 to -50 dB to MVIP/H.100
Automatic Gain Control (AGC): Programmable from API
Automatic Volume Control (AVC): Programmable from API
Activity Detection: Programmable from API
Frequency Response: 300 - 3400 Hz (+/- 3dB) |
DTMF Tone
Detection
DTMF digits: 0 - 9, *, #, A, B, C, D
Dynamic range: -38 dBm to 0 dBm
Minimum tone detection: 40 ms / programmable
Interdigit timing: 40 ms min.
Acceptable twist: Per LSSGR sec. 6, 8 dB forward,
4 dB reverse
Frequency variation: Accept all +/- 1.5%,
reject all +/-2.5%
Noise tolerance: Per LSSGR sec. 6
Talk off: Bellcore TR-TSY-000762
Safety and
Certifications
Telecom: DOC
Emissions: FCC Part 15 class A · EN 55022
Immunity: EN 55024
Safety: EN 60950
Estimated MTBF: 250,000 hours per Bellcore Method I |
Audio
Digitizing (Encoding & Decoding)
5.3 Kb/s G.723.1
6.3 Kb/s G.723.1
8 Kb/s: G.729A
13 Kb/s: GSM 6.10, Microsoft GSM
16 Kb/s: G.726
24 Kb/s: G.726, OKI
32 Kb/s: G.726, OKI
40 Kb/s: G.726
64 Kb/s: µ-law or A-law per G.711,
8 bit linear PCM (signed & unsigned)
96 Kb/s 6 Khz 16 bit linear PCM(signed)
128 Kb/s: 16 bit linear PCM (signed & unsigned)
Wave file formats: Microsoft GSM, Linear signed
8 & 16-bit PCM
Digitization selection: Programmable per channel, independent
for encode and decode |
Models Available
P3209/DP3209-eh: Single E1/T1
DP6409/DP6409-eh: Dual E1/T1
* -eh denotes PCI-E slot card
|
|
Part number |
|
| 910-0308-002 |
DP3209 |
| 910-0324-001 |
DP6409 |
| 910-0703-001 |
DP3209-eh |
| 910-0703-002 |
DP6409-eh |
|
|
|
|
|
|
|
|
